az ru en

Products


Paints

MEGA Paints

FAB MEGA İPƏK






INTERIOR BRIGHT PAINT

DESCRIPTION:

Acrylic copolymer based, bright looking, repeatedly washable, easily applicable, hard, high quality decorative interior topcoat paint with high adhesion and covering power

FEATURES:

MEGAİPƏK (441) is high quality, repeatedly washable, non-cracking and non-flowing interior wall paint with the ability of high adhesion and covering to all kinds of surfaces. The impact and scratch resistant. Can be used in every season. It has a high ability to breathe. Environmental clean, do not smell, environmental friendly

APPLICATION:

MEGAİPƏK (441) is used as a finishing decorative bright paint on interior surfaces of buildings, on the surfaces previously painted with synthetic and water based paints, on all kinds of plastered surfaces, paintable wallpapers. The surfaces prior to the application should be cleaned of dust, dirt and oils, roughness should be smoothed and the surface should be dry. Wait 4 weeks before painting the newly pasted surfaces. If before the application there appeared the salinization on the plastered surface it should be cleaned with damp automobile brush and then treated with FABKIM HIDROSTOP 500 mixed with the same ratio of water. 24 hours later the black plastered surfaces should be treated with FABBINDER (340) mixed with water in 1:7 ratios (1 ratio of FABBINDER (340), 7 ratios of water). Wait at least 5-6 hours after using FABBINDER (340). Non plastered surfaces should be plastered with plaster FABGIPS TƏK ASTAR. In order to get better result the surfaces treated with binder or plastered surfaces should be applied with stucco FABGIPS ASTAR and then covered with coating plaster FABGIPS ÜZLÜK. After the wall has completely dried it should be sanded with sanding paper. The surfaces previously painted with synthetic and water based paints should be sanded, parts needing repair (swollen parts, cracks, etc.) should be repaired with FABGIPS materials. After being sanded the surface should be treated with FABBINDER (340) mixed with water in 1:7 ratios (1 ratio of FABBINDER (340), 7 ratios of water). Wait at least 5-6 hours after using FABBINDER (340). In order to get more brightness it is recommended to use 1 coat of MEGAASTAR (438) first. Wait at least 5-6 hours and mix MEGAİPƏK (441) with water to 15-20% and depending on desired covering and color apply with the help of DEKOR EXPORT RULO (1080), brush or pulverizing. Wait at least 5-6 hours between coats. In order to get more brightness the third coat can be applied. Pulverizing will make better result than rolling. Wash the tools with water after use

THINNING:

Mix with 15-20% of water

DRYING TIME:

(20°C/65%HR): dries within 1 hour, time between coats – 5-6 hours, full drying – 24 hours

CONSUMPTION:

depending on the smoothness of the surface and the thickness of the coat 1kg. of MEGAİPƏK (441) can cover 9-12 m2 of area in 1 coat (at wet film thickness of100-120µ, mixed with water to 15-20%)

NOTE:

During the application the surface and room temperature should be between +5°C and +30°C

SHELF LIFE:

2 years. The ideal storage temperature is between +10°C and +30°C. (In an unopened original container in cool, safe from freezing and direct influence of the sun rays)

SAFETY MEASURES:

S 2 Keep far from children. S 46 If swallowed immediately call for a doctor and show him the box or label

PROBLEMS OCCURING WHILE KEEPING AND USING:

PROBLEMS OCCURING WHILE KEEPING AND USING: Incrustation in closed container is caused by air leakage; sediment is caused by keeping in a colder or hotter environment. Appearing of mold on the surfaces painted with water-based paints is caused by the excessive moisture around, by the exposure of the walls to water from outside, from ceiling and foundation and poor heating insulation. Light cracks appearing in application of acrylic paints are caused by the excessive thick coats of paint, hot surface while painting, windy weather, adding filling agent such as calcite to the prepared paint and the excessive use of grounds. The excessive thick coat of paint or the excessive use of thinners can cause flowing and waving look. If the surface is too dirty or in case of insufficient thinning of paint it can come unstuck and be stripped off. The direct sun rays falling on the wall being painted can cause poor adhesion of the paint because of its fast drying. If you are having problems like this please contact Technical Service with any problem which you are interested in and take a party number on the container with you

THE MANUFACTURER IS NOT RESPONSIBLE FOR MISUSE

Facebook Twitter