az ru en

Products


Paints

MEGA Paints

FAB MEGAFASKO






High quality decorative exterior topcoat paint with high adhesion and covering power

DESCRIPTION:

Acrylic copolymer based, matt looking, breathing, outdoor sun lights and water resistant, easily applicable, high quality decorative exterior topcoat paint with high adhesion and covering power

FEATURES:

MEGAFASKO is non-cracking and non-flowing, matt looking exterior paint with high adhesion and covering power to all kinds of surfaces. The impact and scratch resistant paint with high breathing ability. Can be used in every season. Environmental clean, do not smell, environmental friendly

APPLICATION:

MEGAFASKO is used as topcoat paint on exterior surfaces of the buildings, on the surfaces previously painted with water based paints and all kinds of plastered surfaces. The surfaces prior to the application should be dry, cleaned of dust, dirt and oils, roughness should be smoothed. Wait 4 weeks before painting the newly pasted surfaces. If before the application there appeared the salinization on the plastered surface it should be cleaned with damp automobile brush and then treated with FABKIM HIDROSTOP mixed with the same ratio of water. 24 hours later in order to get better effect the plastered surfaces should be treated with FABBINDER mixed with water in 1:7 ratios (1 ratio of FABBINDER, 7 ratios of water). Wait at least 5-6 hours after using FABBINDER and apply FAB AKRILIK MƏCUN. After the wall has completely dried it should be sanded with sanding paper. The surfaces previously painted with water based paints should be sanded, parts needing repair (swollen parts, cracks, etc.) should be repaired with FAB AKRILIK MƏCUN. After being sanded the surface should be treated with FABBINDER mixed with water in 1:7 ratios (1 ratio of FABBINDER, 7 ratios of water). Wait at least 5-6 hours after using FABBINDER. In order to get better surface it is recommended to use 1 coat of MEGA ASTAR first. When needed to use on exterior surfaces previously painted with synthetic paints it should be sanded first and after being cleaned of sands should be covered with 1 coat of FAB KEÇİD ASTARI. Later mix MEGAFASKO with water to 15-20% and apply with the help of DEKOR SUPERLUX RULO, brush or pulverizing. Wait at least 5-6 hours between coats. Wash the tools with water after use

THINNING:

Mix with 15-20% of water

DRYING TIME:

Touch dry - 1 hour, time between coats – 5-6 hours, full drying – 24 hours (20°C/65%HR)

CONSUMPTION:

Depending on smoothness of the surface and thickness of the coat 1kg. of MEGAFASKO can cover 8-10 m2 of area in 1 coat (at wet film thickness of100-120µ, mixed with water to 15-20%)

NOTE:

During the application the surface and room temperature should be between +5°C and +30°C

SHELF LIFE:

2 years. The ideal storage temperature is between +10°C and +30°C. (In an unopened original container in cool, safe from freezing and direct influence of the sun rays)

SAFETY MEASURES:

S 2 Keep far from children. S 46 If swallowed immediately call for a doctor and show him the box or label

PROBLEMS OCCURING WHILE KEEPING AND USING:

Incrustation in closed container is caused by air leakage; sediment is caused by keeping in a colder or hotter environment. Appearing of mold on the surfaces painted with water-based paints is caused by the excessive moisture around, by the exposure of the walls to water from outside, from ceiling and foundation and poor heating insulation. Light cracks appearing in application of acrylic paints are caused by the excessive thick coats of paint, hot surface while painting, adding filling agent such as calcite to the prepared paint and the excessive use of grounds. The excessive thick coat of paint or the excessive use of thinners can cause flowing and waving look. If the surface is too dirty or in case of insufficient thinning of paint it can come unstuck and be stripped off. The direct sun rays falling on the wall being painted can cause poor adhesion of the paint because of its fast drying. If you are having problems like this please contact Technical Service with any problem which you are interested in and take a party number on the container with you

THE MANUFACTURER IS NOT RESPONSIBLE FOR MISUSE

Facebook Twitter